產品詳情
全系列型號TOGNELLA流量控制閥FT-573/R使用方法
一級保養工作是在例行保養得基礎上進行的,重點工作內容是潤滑、緊固并檢查各有關部位及其清潔工作.二級保養工作以檢查、調整為重點。具體要檢查發動機、離合器、變速器、傳動構件、轉向和制動構件。三級保養重點是檢測、調整、排除故障隱患及平衡各部件的磨損程度。要對影響設備使用性能的部位及有故障征兆的部位進行診斷檢測和狀態性檢查,進而完成必要的更換、調整及故障排除等工作。換季保養是指包設備每年入夏和入冬前應重點對燃潤系統、液壓系統、冷卻系統和啟動系統等構件的檢測和修復。
EI(electronics-inc) 100 MagnaValve 流量閥
EI(electronics-inc) 500-24 MagnaValve 流量閥
EI(electronics-inc) 500-P MagnaValve 流量閥
EI(electronics-inc) 590-24 MagnaValve 流量閥
EI(electronics-inc) LP-24 MagnaValve 流量閥
EI(electronics-inc) LP-24HT MagnaValve 流量閥
EI(electronics-inc) LP2000 MagnaValve 流量閥
EI(electronics-inc) LP2000VAR MagnaValve 流量閥
EI(electronics-inc) VLP-24 MagnaValve 流量閥
EI(electronics-inc) VLP-24HT MagnaValve 流量閥
EI(electronics-inc) VLP1000 MagnaValve 流量閥
EI(electronics-inc) VLP1000VAR MagnaValve 流量閥
EI(electronics-inc) WM 3000-24 MagnaValve 流量閥
EI(electronics-inc) 578 MagnaValve 流量閥
EI(electronics-inc) 579 MagnaValve 流量閥
EI(electronics-inc) 580 MagnaValve 流量閥
EI(electronics-inc) 590 MagnaValve 流量閥
EI(electronics-inc) 576-24 流量閥
EI(electronics-inc) 577-24 流量閥
EI(electronics-inc) 578-24 流量閥
EI(electronics-inc) 579-24 MagnaValve 流量閥
EI(electronics-inc) 580-24 MagnaValve 流量閥
EI(electronics-inc) 590-24 MagnaValve 流量閥
EI(electronics-inc) 700-24 MagnaValve 流量閥
EI(electronics-inc) 178-DC MagnaValve 流量閥
EI(electronics-inc) 179-AC MagnaValve 流量閥
EI(electronics-inc) 179-DC MagnaValve 流量閥
EI(electronics-inc) 180-AC MagnaValve 流量閥
EI(electronics-inc) 180-DC MagnaValve 流量閥
EI(electronics-inc) 190-AC MagnaValve 流量閥
EI(electronics-inc) 190-DC MagnaValve 流量閥
EI(electronics-inc) AC Controller MagnaValve 流量閥
EI(electronics-inc) AC-24 MagnaValve 流量閥
EI(electronics-inc) FC MagnaValve 流量閥
EI(electronics-inc) FC-24 MagnaValve 流量閥
EI(electronics-inc) MC MagnaValve 流量閥
EI(electronics-inc) POT-24 MagnaValve 流量閥
EI(electronics-inc) VARIAC MagnaValve 流量閥
EI(electronics-inc) electronics-inc 70-24 流量閥
EI(electronics-inc) electronics-inc MFD-P1 流量閥
EI(electronics-inc) electronics-inc MFD-4 流量閥
EI(electronics-inc) electronics-inc MFD-250 流量閥
一般說來,按照人們習慣上的概念,數值越大,硬度越高。因此采用一個常數c減去h來表示硬度的高低。并用每.2㎜的壓痕深度為一個硬度單位。由此獲得的硬度值稱為洛氏硬度值,用符號HR表示。式中,c為常數(對于HRHRA,c取.2;對于HRB,c取.26)。由此獲得的洛氏硬度值HR為一無名數,試驗時一般由試驗機指示器上直接讀出。常用洛氏硬度標尺及適用范圍上述洛氏硬度的三種標尺中,以HRC應用多,一般經淬火處理的鋼或工具都采用HRC測量。