產品詳情
全系列型號SCHNEIDER絕緣監測置IMD-IM20使用方法
且拉西環填料的內表面潤濕率較低,因而傳質速率也不高。鮑爾環(Pallring)填料.在拉西環的基礎上發展起來的鮑爾環是在的側壁上開一層或兩層長方形小孔,小孔的母材并不脫離側壁而是形成向內彎的葉片。比之拉西環,鮑爾環不僅具有較大的生產能力和較低的壓降,且分離效率較高,溝流現象也大大降低。階梯環填料(Stairring);階梯環填料的結構與鮑爾環填料相似,環壁上開有長方形小孔,環內有兩層交錯45的十字形葉片,環的高度為直徑的一半,環的一端成喇叭口形狀的翻邊。
EI(electronics-inc) 100 MagnaValve 流量閥
EI(electronics-inc) 500-24 MagnaValve 流量閥
EI(electronics-inc) 500-P MagnaValve 流量閥
EI(electronics-inc) 590-24 MagnaValve 流量閥
EI(electronics-inc) LP-24 MagnaValve 流量閥
EI(electronics-inc) LP-24HT MagnaValve 流量閥
EI(electronics-inc) LP2000 MagnaValve 流量閥
EI(electronics-inc) LP2000VAR MagnaValve 流量閥
EI(electronics-inc) VLP-24 MagnaValve 流量閥
EI(electronics-inc) VLP-24HT MagnaValve 流量閥
EI(electronics-inc) VLP1000 MagnaValve 流量閥
EI(electronics-inc) VLP1000VAR MagnaValve 流量閥
EI(electronics-inc) WM 3000-24 MagnaValve 流量閥
EI(electronics-inc) 578 MagnaValve 流量閥
EI(electronics-inc) 579 MagnaValve 流量閥
EI(electronics-inc) 580 MagnaValve 流量閥
EI(electronics-inc) 590 MagnaValve 流量閥
EI(electronics-inc) 576-24 流量閥
EI(electronics-inc) 577-24 流量閥
EI(electronics-inc) 578-24 流量閥
EI(electronics-inc) 579-24 MagnaValve 流量閥
EI(electronics-inc) 580-24 MagnaValve 流量閥
EI(electronics-inc) 590-24 MagnaValve 流量閥
EI(electronics-inc) 700-24 MagnaValve 流量閥
EI(electronics-inc) 178-DC MagnaValve 流量閥
EI(electronics-inc) 179-AC MagnaValve 流量閥
EI(electronics-inc) 179-DC MagnaValve 流量閥
EI(electronics-inc) 180-AC MagnaValve 流量閥
EI(electronics-inc) 180-DC MagnaValve 流量閥
EI(electronics-inc) 190-AC MagnaValve 流量閥
EI(electronics-inc) 190-DC MagnaValve 流量閥
EI(electronics-inc) AC Controller MagnaValve 流量閥
EI(electronics-inc) AC-24 MagnaValve 流量閥
EI(electronics-inc) FC MagnaValve 流量閥
EI(electronics-inc) FC-24 MagnaValve 流量閥
EI(electronics-inc) MC MagnaValve 流量閥
EI(electronics-inc) POT-24 MagnaValve 流量閥
EI(electronics-inc) VARIAC MagnaValve 流量閥
EI(electronics-inc) electronics-inc 70-24 流量閥
EI(electronics-inc) electronics-inc MFD-P1 流量閥
EI(electronics-inc) electronics-inc MFD-4 流量閥
EI(electronics-inc) electronics-inc MFD-250 流量閥
為了提高產量干燥機滾筒做的過長;直徑做的過大;不能充分利用;造成熱能流失;設備占地面積大。為了提高產量進口溫度過高;出口溫度過高;造成能源浪費。同時也造成了被烘干物料品質下降;物料色澤嚴重變黑;甚至糊料很多。滾筒內風速過低,造成物料與熱風的動態和靜態接觸力度松弛,從而造成烘干設備效率低下。只有順流烘干,且干燥過程中飽和的水蒸氣又不能及時排出,這樣水蒸氣在滾筒內運行距離過長,造成水分被干物料重新吸收。