醫院專用便攜式小型靜音無油空壓機

數量(臺) 價格
1000 2888.00元/臺
  • 最小起訂: 1臺
  • 發貨地址: 上海 奉賢區
  • 發布日期:2019-11-19
  • 訪問量:2233
咨詢電話:137-6112-3991
打電話時請告知是在機電之家網上看到獲取更多優惠。謝謝!
6

倉恒機械(上海)有限公司

實名認證 企業認證
  • 聯系人:吳興照
  • 手機:13761123991
  • 電話:021-13608853560
  • 營業執照:已審核 營業執照
  • 經營模式: 代理商-私營獨資企業
  • 所在地區:上海 嘉定區
  • 家家通積分:70分
添加微信好友

掃一掃,添加微信好友

詳細參數
品牌倉恒型號550W
工作原理速度式冷卻方式風冷
排氣量類型小型排氣量110L,min
排氣壓力類型中壓式排氣壓力0.8MPa
固定方式移動式潤滑情況無油潤滑式
原動機類型電動機驅動氣缸中心線與地面相對位置臥式
壓縮次數單級作用方式單作用式
缸徑×缸數-功率550W
額定轉速1400R.P.M氣桶容積18L
電壓220v噪聲45
適用領域醫院,小型加工廠,牙科專用,實驗室電源型式220V
加工定制外形尺寸其他
重量18kg壓縮介質空氣
用途醫用傳動方式-
產地上海

產品詳情

醫院專用便攜式小型靜音無油空壓機     醫院專用無油空壓機,便攜式靜音無油空壓機,牙科專用型空壓機

一、醫院專用便攜式小型靜音無油空氣壓縮機采用高品質,用途最廣,大流量無油搖擺活塞式的壓縮機作為動力源,能提供穩定的無油氣源,避免油污進入儲氣罐又能避免終端機器的非耐油管因有油而引發故障。其部件均選用優質元器件,整機按照靜音的特點制造,流量大,噪音低,氣源潔凈干燥,遠行平穩,全自動控制,在運行過程中,當氣罐內壓力達到設定的壓力值時,醫院專用無油壓縮機將自動開機或停機。本機適合各種氣動工具的氣源,是您理想的選擇。


醫院專用便攜式小型靜音無油空壓機    醫院專用無油空壓機,便攜式靜音無油空壓機,
  牙科專用型空壓機

二.牙科專用型空壓機使用. 操作注意事項:

Use. Operation cautions: 

1. 使用時應將便攜式靜音無油空壓機水平安放在室內干燥. 清潔. 通風場所,特別注意遠離粉塵之類的范圍,如無法達到要求,必須增加過濾。

one . When using air compressor level should be in indoor dry. Clean. Ventilated place, special attention away from dust and so on range, if cannot meet the requirements, must increase filter.

2. 使用前請檢查空壓機進氣通道有無堵塞,關閉排氣球閥,各元件有無異?,F(xiàn)象。然后將插頭插到電源上,打開開關,空壓機電機即開始啟動,電磁閥動作,整機開始工作。

 Before use, please check the air compressor inlet channel for plugging, closed exhaust valve, each element is abnormal phenomena. Then will plug to power supply, open the switch, air pressure mechanical and electrical machine is started, electromagnetic valve b, the machine began to work. 

3. 壓力表指示壓力升高至設定的壓力時,壓力控制自動斷開,空壓機停止工作。或當因供電中止,壓力升至低與高壓力值之間時而停機,在恢復供電后,氣罐壓力降至低壓力控制點才能工作。

  Pressure gauge indicated pressure rise to set maximum pressure, pressure control automatically disconnect, air compressor stop working. Or when the power supply because of suspension, the pressure to the lowest and highest between sometimes stop, in restore power, tank pressure drop to the lowest pressure control point can work.

4. 接好排氣閥嘴至所有氣源設備管道,打開排氣閥門即可開始向設備供氣,當壓力表指示壓力降至設定的低壓力時,壓力控制自動閉合,醫院專用無油空壓機重新啟動(低壓力值和高壓力值根據不同的型號在產品出廠前都已設定好,一般情況下用戶不要擅自調整設定值)。

 Pick good exhaust valve mouth to all air supply equipment pipe, open the exhaust valve can begin to equipment supply, when pressure gauge indicated pressure drop to the minimum set pressure, pressure control automatic closed, air compressor restart (minimum pressure value and highest pressure value according to the different models, before the products leave the factory has been set, usually users don't do STH without authorization adjustment setting).

5. 

1. 如果用戶電源電壓偏低,達不到標準電壓值±10%范圍內,不能強行使用,否則會損壞空壓機電機,應另加電源穩壓器或調壓器,使所使用電壓達到標準電壓值。

If the user power supply voltage on the low side, can not reach the standard voltage value plus or minus 10% range, can't forced to use, otherwise it will damage the air pressure mechanical and electrical machine, should add power voltage regulator or voltage regulator, the use of voltage up to standard voltage value

2. 使用過程中,空壓機儲氣罐里會凝結少量的水分,所以要定期排水,一般每星期排水一次,排水前先關掉電源,打開排氣閥門排盡儲氣罐里的氣體,然后擰開儲氣罐底部塞堵,排完水后,重新裝好即可使用。

 Use process, air compressor gas storage in setting a small amount of water, so want to periodically drainage, general every week a drainage, drainage before you turn off the power supply, open the exhaust valve exhaust all gas storage of gas, and then twist off gas storage tank bottom plug plugging, exhaust the water, reinstall it use.

3. 使用過程中,由于空氣中含有灰塵,所以消聲器要每星期定期清洗一次,清洗前先關閉電源,將消聲器擰下,然后擰下消聲器端蓋,取出里面的濾芯用氣吹洗干凈,重新安裝后即可使用(必要時更換新濾芯)。

4. In use process, because the air containing dust, so muffler to every week periodic cleaning once, before washing off the power supply, will muffler unscrewing, then unscrewing muffler end cover, take out the inside of the filter gas purge clean and reinstall can use (when necessary change new filter).

5. 可調元件壓力控制器上部有一枚調節螺絲,可用來調節加減壓差。壓縮機出廠前已經調好停機壓力,用戶千萬不能自己隨意調節,否則可能會超出整機設計參數,損壞機組活導致壓縮機不能正常運轉。

6. Adjustable element pressure controller upper one pieces of adjusting screw, can be used to regulate and differential pressure. Compressor before they leave the factory has been tuned down pressure, the user must not his adjust at will, otherwise it may exceed the design beters, the damage units to the normal operation of compressor can't live.

7. 壓縮機上配有熱保護器和過電流保護器:電機過熱時保護器會自動斷開;電機堵轉,電壓過高時,過電流保護器會自動斷開,而且兩者都會自動復位,因此檢查時應注意電路是否通暢。

  Compressor with thermal protector and overcurrent protector: motor overheating when protector will automatically disconnect; Motor stall, the voltage is too high, overcurrent protector will automatically disconnect, and both automatic reset, so check should be paid attention to when circuit is obstructed.

醫院專用便攜式小型靜音無油空壓機    醫院專用無油空壓機,便攜式靜音無油空壓機,牙科專用型空壓機

三.保養及維護:

Maintenance and maintenance:

1.為了保證安全,壓縮機工作時嚴禁觸及機上任何元件。

In order to ensure safety, compressor work on it is strictly prohibited to touch any element

2.本機為無油壓縮機,嚴禁加油潤滑。

This machine is oil free compressor, it is strictly prohibited to lubrication

3.本機使用的環境溫度為5-40

This machine use environment temperature of 5 ℃ to 40 ℃

4.清洗時絕對禁止往整機上灑水,應用柔軟干布擦凈上面的灰塵,小心碰壞元件。

When cleaning, absoluby forbidden to on the water, the application of soft dry cloth wipe the dust, careful touch bad element.

5.使用完畢后請切斷電源開關,關閉氣源。

After using please shut off power supply switch, shut off the air.




四.故障分析及排除方法

Failure analysis and elimination b

故障現象

Fault phenomenon 

原因與排除方法

Reason and elimination b

 

壓縮機不運轉,電機無嗡嗡交流聲

Compressor doesn't work, the motor without hum hum

1. 檢查插座有無電源

Check socket for power supply 

2. 檢查過電流保護器和壓力控制器的接線是否接通

Check the overcurrent protector and pressure controller connection are switched on

 

壓縮機味道設定壓力后停機

Compressor taste set the highest pressure shutdown

1. 壓力開關設定值低, 調整設定值至要求值

Pressure switch setting low, adjust the set point to the required value

2. 過電流保護器故障, 更換過電流保護器

Overcurrent protector fault, replace the overcurrent protector

 

不能正常啟動,電機有轉動后即停止,并可聽到電機嗡嗡聲

Can't the normal starting, motor rotation namely after stop, and can hear motor buzz

1. 電壓過低,增加穩壓裝置或待電壓正常后使用

Voltage is too low, increase the voltage stabilizer or stay voltage to normal after use

2. 緩沖罐內氣體為排空后有啟動,多見插頭接觸不良或中間停機時間小于5S,  拔出插頭 或更換插座保證接觸良好

Buffer tank gas for emptying after startup, see more plug bad contact or intermediate down time less than 5 s, pull out plug or replace socket guarantee good contacts

3. 卸壓閥(電磁閥)不排氣, 檢查電磁閥是否有故障(方法:拔出插頭,排盡氣罐氣體,插上插頭,氣壓上升到一定壓力時拔出插頭,電磁閥應排氣)

Pressure relief valve (electromagnetic valve) no exhaust, check the electromagnetic valve if there is a fault (bs: pull out plug, row do tank gas, insert the plug, pressure rises to a certain pressure pull out plug, electromagnetic valve should be exhaust)

4. 壓縮機電容損壞后電容量減少, 更換電容

Compressor capacitance in damaged electric capacity to reduce, replace the capacitance

壓縮機連續運轉,但壓力達不到停止壓力或關閉排氣球閥時,達到停止壓力時的時間增長

Compressor continuous operation, but the pressure can not reach the stop pressure or close exhaust valve, pressure to stop the time when the growth

1. 壓縮機及管路系統空氣泄露, 檢查各接頭處有無漏氣現象

Compressor and piping system air leak, check the layup for gas leakage phenomenon 

2. 壓縮機機頭故障,打開缸蓋檢查閥門有無積碳閥片是否翹曲. 或皮碗磨損,   與生產廠商聯系

Compressor head fault, open the cylinder head check valve for carbon deb valve plate is warping. Or cup wear, and manufacturers contact

停機時關閉排氣球閥氣壓下降

Stop close exhaust valve pressure drop

 

1. 氣罐各個接頭漏氣, 加緊擰緊街頭

2. Tank each joint gas leakage, tightening screw down the street

3. 單向閥不密封, 清洗.清理閥芯或更換單向閥或閥芯

Check valve no seal, cleaning. Cleaning valve core or replace check valve or valve core

超過壓力設定值不停機

More than pressure maximum set point don't stop

1. 壓力控制器壞, 調整或更換壓力控制器

Pressure controller bad, adjust or change pressure controller 

在壓縮機工作壓力范圍,安全閥排氣

In the compressor working pressure range, relief valve exhaust

1. 安全閥彈簧力減弱,調整螺母松動, 調節安全法調整螺母至安全閥工作壓力排氣,并鎖緊螺母。更換新的安全閥

The relief valve spring force is abate, adjusting nut loose, adjust safety adjusting nut to relief valve working pressure exhaust, and lock nut. Replacement of the relief valve 

.產品結構及名稱   

Product structure and name                       

序號

Serial number

名稱

  name

序號

Serial number

名稱

name

序號

Serial number

名稱

name

1

風罩

The wind hood

11

缸蓋

Cylinder head

21

曲軸

crankshaft

2

風扇

fan

12

缸蓋螺釘

Cylinder screw

22

軸承

bearing

3

箱體

housing

13

連接管密封圈

Connecting pipe sealing ring

23

緊定螺釘

Set screw

4

連桿

Connecting rod

14

連接管

Connecting pipe

24

圓柱頭螺釘

Cylinder head screw

 

5

活塞皮碗       Piston cup

15

盤頭螺釘

Supplied pan-head screws

25

引出線保護圈

Lead guard circle

6

壓板

clamp

16

限位塊

Limit block

26

電機螺栓

Motor bolt

7

壓板螺釘

Clamp screw

16

出氣閥片

Air outlet valve slice

27

彈簧墊圈

Spring washer

8

氣缸

   cylinder

17

閥板

Valve plate

28

定子

stator

9

氣缸密封圈

Cylinder seal

19

進氣閥片

Inlet valve slice

29

鎖緊螺母

Lock nut

 

 

 


 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 



溫馨提示

  • 還沒找到想要的產品嗎? 立即發布采購信息,讓供應商主動與您聯系!

免責聲明:所展示的信息由會員自行提供,內容的真實性、準確性和合法性由發布會員負責,機電之家網對此不承擔任何責任。機電之家網不涉及用戶間因交易而產生的法律關系及法律糾紛,糾紛由您自行協商解決。
友情提醒:本網站僅作為用戶尋找交易對象,就貨物和服務的交易進行協商,以及獲取各類與貿易相關的服務信息的平臺。為避免產生購買風險,建議您在購買相關產品前務必確認供應商資質及產品質量。過低的價格、夸張的描述、私人銀行賬戶等都有可能是虛假信息,請采購商謹慎對待,謹防欺詐,對于任何付款行為請您慎重抉擇!如您遇到欺詐等不誠信行為,請您立即與機電之家網聯系,如查證屬實,機電之家網會對該企業商鋪做注銷處理,但機電之家網不對您因此造成的損失承擔責任!
您也可以進入“消費者防騙指南”了解投訴及處理流程,我們將竭誠為您服務,感謝您對機電之家網的關注與支持!

您是不是在找